The honest answer up front: a quartz broadcast epoxy floor needs the same low-effort resin routine as any epoxy — sweep or dust-mop regularly, wash with a mild pH-neutral cleaner, skip acids and harsh solvents — but with one real difference: the textured, granular surface that gives it genuine wet-floor grip also holds dirt harder than a smooth epoxy, so it wants a deck brush or a floor scrubbing machine into the texture, not a light surface mop. Get that one trade-off right and it is one of the easiest commercial floors we install to keep looking and performing the way it was specified.
Why this floor cleans differently from a smooth epoxy
Our general epoxy care guide covers the routine for a smooth, glossy epoxy — poured, metallic or flake — where a mop glides straight over the surface. Quartz broadcast epoxy is built the opposite way on purpose: coloured quartz sand is broadcast into the wet resin body coat so the grains stand shoulder to shoulder, then sealed under clear topcoats, so the finished floor keeps a real mineral tooth underfoot. That tooth is the entire reason facilities specify this system for washrooms, commercial kitchens and wet process zones — but a textured surface has more surface area for grit and grease to hide in than a flat one, and a light mop only ever cleans the peaks, not the low points between the grains.
The routine that actually works
Daily-ish: sweep or dust-mop before anything gets ground in. Loose grit dragged across the textured surface by shoes, trolleys or racking wheels works its way into the low points between the quartz grains if it isn’t lifted off first — the same abrasion risk any resin floor faces, just concentrated by the texture here.
Regular: deck brush or a rotary scrubbing machine with a mild pH-neutral detergent. This is the one real departure from a smooth epoxy’s care routine. Warm water and a stiff-bristled deck brush — or, for a larger commercial floor, a mechanical scrubber-dryer — work the cleaner down into the texture rather than skating across the top of it. A light microfibre mop leaves the grip intact but the grime behind it.
Rinse and squeegee. Because the floor is sealed rather than porous, a proper rinse after scrubbing lifts the loosened dirt away instead of just redistributing it across the surface — important in a washroom or kitchen floor that’s coved up the wall, where standing detergent residue at the base of the cove reads as grime even after a clean.
What to avoid
- Acids, caustic degreasers at full strength and aggressive solvents — the resin resists far more chemistry than a mineral floor, but repeated strong-chemical “deep cleans” dull the clear seal coats over time, same as any epoxy.
- Steam cleaning — stresses the resin bond over repeated use; warm water is the safer long-term choice.
- Skipping the scrub for a quick mop, week after week. A quartz broadcast floor mopped like a smooth epoxy will look clean on the surface while dirt quietly builds in the texture — the eventual deep clean to shift it is far harder than keeping ahead of it with routine scrubbing.
No colour-fade reseal cycle — with one honest caveat
The coloured quartz sand is locked inside the resin body, not painted on top of it, so ordinary cleaning and foot traffic don’t wear the colour away the way a painted floor can fade. The caveat the technology page is upfront about: like every epoxy, it ambers slowly under direct UV, which is why this is an indoor system. A quartz broadcast floor near a sun-flooded glass frontage is a spec conversation worth having before installation, not a cleaning problem to manage afterward.
When the seal coat needs attention, not the whole floor
Under heavy point traffic — a fixed workstation, a repeated trolley path — the clear seal coat over the quartz can wear thinner than the field around it well before the sand body underneath is compromised. That is a localised reseal, not a floor replacement: the worn patch gets cleaned, lightly prepared and resealed, and it blends back into a floor that was never going anywhere. Left unattended for years, a genuinely worn-through patch can expose the quartz grain to more staining and moisture ingress than the sealed floor around it, which is the honest reason to flag it early rather than wait.
The bottom line
Sweep it daily, scrub it into the texture with a mild cleaner and a deck brush or machine rather than a light mop, rinse it properly, and skip the acids and steam — that is genuinely the whole routine, and the one habit that separates a quartz broadcast floor that stays gripping and hygienic for years from one that quietly loses both.
Specifying or maintaining a wet-area or commercial floor and want the cleaning routine matched to how it will actually be used? Send us the space on WhatsApp or call +971 4 587 7086. 8+ years in the UAE, and RBS is responsible for every job, start to finish — we’ll tell you honestly what it needs.
Related guides
Get an exact price
Tell us about your space.
Send a few photos and rough sizes on WhatsApp — we'll come back with a real number.